Measurement and Production Engineering MCQs | BME MCQs

by

Hello Friends !!! I am from quickstudyhelper.com. In today’s post, we are going to see very important ‘Measurement and Production Engineering MCQs’ which help you in your examination. If you are preparing for a competition exam, board exam, and engineering exam then you can read these MCQs. These MCQs are based on RGPV syllabus but it also important for any other examination.

50 Most Important RGPV Unit – 2 MCQs

Q1. Form cutting can be performed more effectively by the ______ milling machine.

  1. horizontal
  2. vertical
  3. can’t say anything
  4. none of these

Answer: – 1) horizontal

Q2. In cryogenic system work is at

  1. zero temperature
  2. medium temperature
  3. extremely high temperature
  4. extremely low temperature

Answer: – 4) extremely low temperature

Q3. In cryogenic system, nuclear systems work at

  1. zero temperature
  2. medium temperature
  3. very high temperature
  4. very low temperature

Answer: – 3) very high temperature

Q4. The melting point at which ice a solid turns to water a liquid is

  1. 44° F
  2. 35° F
  3. 32° F
  4. 58° F

Answer: – 3) 32° F

Q5. For sub-zero temperature, the datum points used are freezing points of

  1. Nickel
  2. Mercury
  3. Platinum
  4. Tungsten

Answer: – 2) Mercury

Q6. Which instrument is not used for measurement of temperature in engineering applications?

  1. Liquid-in-glass thermometers
  2. Pressure gage thermometers
  3. Liquid thermometers
  4. Resistance thermometers

Answer: – 3) Liquid thermometers

Q7. In liquid-in-glass Thermometers two types of bulb use at one end and another end these are

  1. Large at one end and small at other end
  2. Small at one end and large at other end
  3. Large at one end and large at other end
  4. Small at one end and small at other end

Answer:- 3) Large at one end and small at another end

Q8. Alcohol is used for measuring lower temperature in the range

  1. -65°C to 75° C
  2. 65°C to 75°C
  3. -35°C to 75°C
  4. 35°C to 75°C

Answer: – 1) -65°C to 75° C

Q9. The length column to change in temperatures is

  1. Directly proportional
  2. Inversely proportional
  3. Not proportional
  4. Both 1 & 2

Answer:- 3) Not proportional

Q10. The length of the tube may be as long as

  1. 60 meters
  2. 65 meters
  3. 70 meters
  4. 75 meters

Answer: – 4) 75 meters

Q11. In Resistance Thermometers the thermal coefficient of resistivity should be

  1. low
  2. medium
  3. high
  4. zero

Answer: – 3) high

Q12. The drilling machine was primarily designed to originate a _____

  1. Flat surface
  2. Cylindrical surface
  3. Taper surface
  4. None of them

Answer: – 4) None of them

Q13. Thermostats are temperature measuring

  1. Scale
  2. Element
  3. Machine
  4. Both 1 & 3

Answer: – 2) Element

Q14. Thermistors compared to metals, the change in resistance is large in thermistors. In their case

  1. resistance decrease with increase in temperature
  2. resistance increase with decrease in temperature
  3. resistance decrease with decrease in temperature
  4. resistance increase with increase in temperature

Answer: – 1) resistance decrease with increase in temperature

Q15. The copper-constantan thermocouple is used in thermocouple is used in the range

  1. -20°C to 500°C
  2. -20°C to 800°C
  3. 1200°C to 1500°C
  4. -200°C to 350°C

Answer: – 4) -200°C to 350°C

Q16. The voltage output of thermocouples is

  1. Volts
  2. Milli-volts
  3. Maga-volts
  4. Ampere

Answer: – 2) Milli-volts

Q17. Change in color is due to the dominance of higher frequencies in the spectrum at

  1. zero temperature
  2. lower temperatures
  3. medium temperatures
  4. higher temperatures

Answer: – 3) medium temperatures

Q18. A manometer is used for measuring

  1. Pressure
  2. Speed
  3. Fathometer
  4. Density

Answer: – 1) Pressure

Q19. Which of the following quantities can be measured using bellows?

  1. Absolute pressure
  2. Gauge pressure
  3. Differential pressure
  4. All of the mentioned

Answer: – 4) All of the mentioned

Q20. If a pressure range of 0 to 1 inch of water is to be measured and recorded, an instrument capable of doing this would be

  1. A bellows
  2. A bell with a liquid seal
  3. A bourdon tube
  4. A mercury manometer

Answer: – 2) A bell with a liquid seal

Q21. In Bourdon tube pressure gages, the arc of the Bourdon tube is usually

  1. Less than 90°
  2. Less than 180°
  3. Less than 360°
  4. More than 180°

Answer: – 3) Less than 360°

Q22. The rate of change of displacement

  1. Force
  2. Flow
  3. Velocity
  4. Speed

Answer: – 3) Velocity

Q23. First converting the linear displacement to angular displacement

  1. Velocity
  2. Speed
  3. Force
  4. Flow

Answer: – 1) Velocity

Q24. Tachometers have a permanent magnet type of

  1. AC generator
  2. DC generator
  3. both 1 & 2
  4. none of them

Answer: – 3) both 1 & 2

Q25.  In ________ velocity of the fluid is constant on every point at a specific time.

  1. Steady flow
  2. Rotational flow
  3. Non steady flow
  4. None of the these

Answer: – 1) Steady flow

Check Out –

Q26. Which of the following represents the correct relation between flow rate and area of pipe?

  1. Direct proportionality
  2. Inverse proportionality
  3. Equal
  4. None of the them

Answer: – 1) Direct proportionality

Q27. Electrical strain gauge works on the principle of

  1. Variation of capacitance
  2. Variation of resistance
  3. Variation of inductance
  4. Variation of area

Answer: – 2) Variation of resistance

Q28. Bonding element in a strain gauge must have __________ insulation resistance

  1. Zero insulation resistance
  2. Low insulation resistance
  3. High insulation resistance
  4. Infinite insulation resistance

Answer: – 3) High insulation resistance

Q29. Dynamic strain measurements use

  1. Brass iron alloy
  2. Iron aluminium alloy
  3. Nickel cadmium alloy
  4. Nickel chromium alloy

Answer:- 4) Nickel chromium alloy

Q30. Which type of surface is produced in facing operation

  1. Cylindrical
  2. Flat
  3. Taper
  4. None of them

Answer:- 2) Flat

Q31. Which of the following operation, we can’t perform on drilling machine?

  1. Reaming
  2. Tapping
  3. Lapping
  4. None of these

Answer: – 4) None of these

Q32. Which of the following device can be used for force measurement?

  1. Beams
  2. Bellows
  3. Capsule
  4. Bourdon tube

Answer: – 1) Beams

Q33. Which of the following can be measured using a Ring-type load cell?

  1. Large weight
  2. Small weight
  3. Both large and small weight
  4. None of these

Answer: – 2) Small weight

Q34. Which of the following conversion is correct for load cell?

  1. Force to strain
  2. Force to displacement
  3. Force to voltage
  4. Both force to strain and force to displacement

Answer: – 4) Both force to strain and force to displacement

Q35. Which of the following represents a moment of inertia of force acting tangential to a cylindrical rod?

  1. FR
  2. F/R
  3. F²R
  4. FR²

Answer: – 1) FR

Q36. Which of the following can be well suited for a flat-spiral spring device?

  1. Used for a very high torque range
  2. Used for a very low torque range
  3. Used for all ranges of torque
  4. None of these

Answer: – 2) Used for a very low torque range

Q37. Which of the following represents the correct relationship between angular displacement and torque?

  1. 90° with each other
  2. Parallel to shaft axis
  3. Perpendicular to shaft axis
  4. 45° from shaft axis

Answer: – 4) 45° from the shaft axis

Q38. Which of the following is caused by careless handling?

  1. Systematic error
  2. Gross error
  3. Random error
  4. None of them

Answer:- 2) Gross error

Q39. Which of the following represents an SI unit of luminous intensity?

  1. Lumen
  2. Dioptre
  3. Candela
  4. None of them

Answer: – 3) Candela

Q40. Which of the following error is caused by poor calibration of the instrument?

  1. Random error
  2. Gross error
  3. Precision error
  4. Systematic error

Answer: – 4) Systematic error

Q41. A discussion of uncertainty is critical for

  1. Characterization of risk
  2. Chemical analysis
  3. Pathway analysis
  4. Data calculation

Answer: – 1) Characterization of risk

Q42. An uncertainty analysis is additionally useful to weigh the benefits against the

  1. Costs of alternative remedial actions
  2. Chemical plans
  3. Exposure plans
  4. Toxicity actions

Answer: – 1) Costs of alternative remedial actions

Q43. Why is the caliper principle used?

  1. For measuring dimensions with vernier capiler
  2. For measuring dimensions with micrometre
  3. For circular divisions
  4. For checking flatness

Answer:- 4) For circular divisions

Q44. How many marks are needed to mark a circular table into 180° divisions using caliper principle?

  1. 1
  2. 2
  3. 3
  4. 4

Answer: – 4) 4

Q45. What is the least count of a micrometer?

  1. 0.01 mm
  2. 0.02 mm
  3. 0.1 mm
  4. 0.2 mm

Answer: – 1) 0.01 mm

Q46. How many divisions are graduated on thimble?

  1. 20
  2. 25
  3. 45
  4. 50

Answer: – 4) 50

Q47. Which of the following is not a common basic form of slip gauge?

  1. Gauge Blocks
  2. Johannes Gauges
  3. Linear Gauges
  4. Gage Blocks

Answer: – 3) Linear Gauges

Q48. Where the spirit level is present in a combination set?

  1. Centre head
  2. Squaring head
  3. Scale
  4. There is no spirit level on combination set

Answer: – 2) Squaring head

Q49. Which is not a part of the combination set?

  1. Slip gauge
  2. Scriber point
  3. Spirit level
  4. Centre head

Answer:- 1) Slip gauges

Q50. Which machine tool is known as the mother machine tool?

  1. Drill
  2. Milling
  3. Lathe
  4. None of these

Answer: – 3) Lathe

Download Measurement and Production Engineering MCQs PDF

If you want to study offline or print out these important Measurement and Production Engineering MCQs then you can buy this pdf. Otherwise, you can read it on our website for free.

Download

I hope you liked this post Measurement and Production Engineering MCQs. More resources and study material are available at Quickstudyhelper.com.

Stay Safe, Stay Healthy

Thank You, Visit Again for your help.

Leave a Comment